Search found 120 matches

by om_tech_support_KR
Fri Jun 11, 2021 7:58 am
Forum: Stepper Motors and Controls
Topic: Driver Does not respond to pulses
Replies: 3
Views: 41

Re: Driver Does not respond to pulses

Hello, It's recommended to use an oscilloscope to check the pulses going to the CW and CCW pins on the driver to see if correct voltage levels are being observed. The voltage levels of pulse signals are on page 10 of the driver manual. https://www.orientalmotor.com/products/pdfs/opmanuals/HM-60128-8...
by om_tech_support_KR
Thu Jun 10, 2021 9:05 am
Forum: Stepper Motors and Controls
Topic: Driver Does not respond to pulses
Replies: 3
Views: 41

Re: Driver Does not respond to pulses

Hello, When running in 2 pulse mode with the CW input the CCW input should be off and if switching directions there should be a 5 us or more delay between signals. This can be referenced on the timing chart on page 12 of the link below. To verify if driver is receiving correct pulse its best to meas...
by om_tech_support_KR
Tue Jun 01, 2021 11:47 am
Forum: Speed Control Systems
Topic: BMU Series, Clarifications
Replies: 17
Views: 5898

Re: BMU Series, Clarifications

Hello, If this system is installed with no regeneration resistor then there is no additional wiring that needs to be done. If no regeneration resistor is used then the pins 10 and 11 are left unwired on CN5. To try and avoid the AL51 alarm you can try increasing the accel/decel times so it does not ...
by om_tech_support_KR
Thu May 06, 2021 6:59 am
Forum: Speed Control Systems
Topic: BMU Series, Clarifications
Replies: 17
Views: 5898

Re: BMU Series, Clarifications

Hello,

If performing a instantaneous stop with a large inertial load its recommended to use. Also if frequently getting the AL51 then you might need the regeneration resistor.
by om_tech_support_KR
Wed May 05, 2021 6:31 am
Forum: Speed Control Systems
Topic: BMU Series, Clarifications
Replies: 17
Views: 5898

Re: BMU Series, Clarifications

Hello, For the BLE2 system AL51 is a regeneration resistor overheat alarm. We recommend to use the regeneration resistor if using the motor in a vertical application or if instantaneous stop or instantaneous bi-directional operation is performed with a large inertial load. You can reference this ala...
by om_tech_support_KR
Tue May 04, 2021 7:51 am
Forum: Speed Control Systems
Topic: BLV Series Speed Control Modbus
Replies: 1
Views: 139

Re: BLV Series Speed Control Modbus

Hello, To change the Mode setting on the BLV driver via Modbus you would have to write to the the Analog input signal selection register 10E3h (lower). This would be on page 27 of the manual below. The registers for the digital speeds are on page 25. https://www.orientalmotor.com/products/pdfs/opman...
by om_tech_support_KR
Tue May 04, 2021 7:38 am
Forum: Stepper Motors and Controls
Topic: AZD-CD / Modbus
Replies: 3
Views: 309

Re: AZD-CD / Modbus

Hi Lucas, You can also set each parameter individually to see which one is giving you this error message. The sample of this is on page 282 of the manual. Note when you test to run it make sure to write a 0 after you execute your movements. https://www.orientalmotor.com/products/pdfs/opmanuals/HM-60...
by om_tech_support_KR
Mon May 03, 2021 11:20 am
Forum: Speed Control Systems
Topic: BMU Series, Clarifications
Replies: 17
Views: 5898

Re: BMU Series, Clarifications

Hello, Could you verify the alarm code on the controller AL51 is not one of the listed codes. If it is AL21 this is a main circuit overheat where the temperature inside the driver exceeded the alarm detection temperature. You will have to check the ambient temperature and the ventilation condition i...
by om_tech_support_KR
Fri Apr 30, 2021 7:52 am
Forum: Stepper Motors and Controls
Topic: AZD-CD / Modbus
Replies: 3
Views: 309

Re: AZD-CD / Modbus

Hi Lucas, Its recommended to check the switches on the front of the AZD-CD driver to match what is shown on page 281 of the manual below. Switch No.2 of SW1 would need to be on and No.1 and No.2 of TERM would need to be on also. These are the termination resistance. After changing the switches you w...
by om_tech_support_KR
Tue Apr 06, 2021 9:01 am
Forum: Stepper Motors and Controls
Topic: Is there any C++ implementaion for Oriental Motor AZ series.
Replies: 1
Views: 240

Re: Is there any C++ implementaion for Oriental Motor AZ series.

Hello, Unfortunately Oriental Motor does not support C#. If using the Modbus RTU RS-485 AZ driver you would have to find a C#/Modbus library file to be able to communicate with it. With this driver you can program it with our free MEXE02 software and run from the I/O. I will link the software below....
by om_tech_support_KR
Tue Mar 30, 2021 8:36 am
Forum: Linear and Rotary Actuators and Controls
Topic: DRSM60-05A4AZMK, Compact Linear Actuator, Absolute Encoder
Replies: 1
Views: 386

Re: DRSM60-05A4AZMK, Compact Linear Actuator, Absolute Encoder

Hello,

For this application its not recommended to be used in a environment with excessive vibration or with any liquid that could splash on the actuator since this does not have any IP protection. Unfortunately we don't have an actuator that we could recommend in this type of application.
by om_tech_support_KR
Fri Feb 19, 2021 2:37 pm
Forum: Stepper Motors and Controls
Topic: Which AZD Driver is suitable?
Replies: 3
Views: 1000

Re: Which AZD Driver is suitable?

Hello, The Free input should also release the brake when turned on. From the initial post and video looks like you are using a 40:1 gearhead PLE60-40. This could be the force you are feeling when trying to rotate the shaft. To verify if this is the case you can remove the gearhead to see if the moto...
by om_tech_support_KR
Fri Feb 19, 2021 2:02 pm
Forum: Stepper Motors and Controls
Topic: Protection power supply AZD CED and KED
Replies: 1
Views: 348

Re: Protection power supply AZD CED and KED

Hi Lorenzo,

The power supply current capacity listed would be the max current the drivers would draw when paired with those motors. It is recommended to use slow blow type fuses because of the inrush current on power up.
by om_tech_support_KR
Wed Jan 20, 2021 11:46 am
Forum: Stepper Motors and Controls
Topic: Get data from azd-kd in LabVIEW through USB
Replies: 1
Views: 487

Re: Get data from azd-kd in LabVIEW through USB

Hello, The AZD-KD driver does not have direct LabView communication it only has direct RS-485 Modbus RTU communication. There have been customer who have used this driver with LabView but had to download a library. I will link previous forums for reference. Unfortunately, we don't support LabView in...
by om_tech_support_KR
Tue Jan 05, 2021 2:54 pm
Forum: Stepper Motors and Controls
Topic: direct reemplacement for ASX66a
Replies: 1
Views: 482

Re: direct reemplacement for ASX66a

Hello, Thank you for contacting Oriental Motor. In regards to your inquiry the ASX66A unfortunately doesn't have a drop in all in one replacement. The closest option to keep similar RS232 programming would be AZM66AK motor, AZD-K driver and SCX11 controller. The SCX11 controller offers RS232 communi...
by om_tech_support_KR
Thu Dec 17, 2020 8:47 am
Forum: Speed Control Systems
Topic: BLH Series, Brushless DC Motors
Replies: 2
Views: 3658

Re: BLH Series, Brushless DC Motors

Hello, 1. You can connect to the RUN/BRAKE input when input is turned off will perform an instantaneous stop. Note stopping time will depending on the load, the motor will try to stop in shortest time. The sensor should only act as a switch since driver would be supplying voltage to this input alrea...
by om_tech_support_KR
Fri Dec 04, 2020 10:01 am
Forum: Stepper Motors and Controls
Topic: Which AZD Driver is suitable?
Replies: 3
Views: 1000

Re: Which AZD Driver is suitable?

Hello, The driver would depend on the type of signal the driver would be receiving. The AZD-KD can be controlled via RS-485 Modbus RTU and I/O. If controlled via the I/O you would first have to program the positioning points via either RS-485 Modbus RTU or from our free software MEXE02. To trigger t...
by om_tech_support_KR
Fri Dec 04, 2020 9:22 am
Forum: Stepper Motors and Controls
Topic: AZD-Z operation data
Replies: 1
Views: 672

Re: AZD-Z operation data

Hi Jonathan, If using AZD-A or -C when you program the operation data points in the MEXE02 software you can run them from either the MEXE02 software of from the I/O on the CN5 connector. To run them from the I/O you will have to turn on the M0-M7 in a binary configuration to match the data point you...
by om_tech_support_KR
Thu Nov 19, 2020 8:43 am
Forum: Stepper Motors and Controls
Topic: AZD-CD Just read DINn Input signal ?
Replies: 3
Views: 833

Re: AZD-CD Just read DINn Input signal ?

Hello, The process should be. 1. 10 registers from 1080h are set to 0 2. Save to non-volatile memory register 0193h 3. Either do a configuration register 018Dh or power cycle If you do not save to the non-volatile memory then do a configuration or power cycle then it would still be reading the origi...
by om_tech_support_KR
Tue Nov 17, 2020 2:57 pm
Forum: Stepper Motors and Controls
Topic: AZD-CD Just read DINn Input signal ?
Replies: 3
Views: 833

Re: AZD-CD Just read DINn Input signal ?

Hello, The registers starting with 1080h would be the DIN inputs and when setting them to 0 that would be no function. Since they are C update type they would update after executing the configuration or cycling the power after doing a non-volatile memory write. If you don't write to the non-volatile...
by om_tech_support_KR
Fri Nov 06, 2020 2:58 pm
Forum: Stepper Motors and Controls
Topic: unipolar and bipolar torque
Replies: 1
Views: 571

Re: unipolar and bipolar torque

Hello, When using bipolar configuration it has more torque at the lower speed range and when in unipolar configuration it has a wider speed range. When switching from bipolar series to unipolar configuration there will be a drop in torque. The torque would be around 5.66Ncm in unipolar configuration...
by om_tech_support_KR
Fri Nov 06, 2020 2:46 pm
Forum: Stepper Motors and Controls
Topic: Stepper motor voltage and torque
Replies: 1
Views: 531

Re: Stepper motor voltage and torque

Hello,

For our stepper motors we only show speed torque curves with 24 VDC drivers since this is what it was tested with. The speed range would decrease and torque would drop off faster if used with 12 VDC.
by om_tech_support_KR
Thu Oct 08, 2020 11:43 am
Forum: Speed Control Systems
Topic: Simple FWD-RWD cycle - Possible with BLE2?
Replies: 1
Views: 619

Re: Simple FWD-RWD cycle - Possible with BLE2?

Hello, For the BLE2 to perform this operation you will need a controller to turn on the CW and CCW inputs when using 2-wire mode. If you using 3-wire mode 1 input would become CW/CCW but you would start the motion by have the START/STOP and RUN/BRAKE inputs on. Then it would rotate CW when off and C...
by om_tech_support_KR
Mon Sep 28, 2020 8:43 am
Forum: General Discussion
Topic: Motor E0709-334
Replies: 4
Views: 1367

Re: Motor E0709-334

Hi Vlad,

Unfortunately I do not have who the OEM was that this motor was made for.
by om_tech_support_KR
Fri Sep 25, 2020 9:05 am
Forum: General Discussion
Topic: Motor E0709-334
Replies: 4
Views: 1367

Re: Motor E0709-334

Hi Vlad, Thank you for contacting Oriental Motor. Unfortunately, the part number you have requested E0709-334 is a proprietary product which we had custom built for an original equipment manufacturer. We do not offer after-market support or sale of this product. You would need to contact the maker o...