Search found 8 matches

by saad
Tue Jul 17, 2018 6:52 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hi all, It should work fine, if you have the same motor and controller I have, basically my setup is as follow: AZD-K SCX11 Stepper Motor You need the universal motor driver (SCX-11). I connected it to the PC via USB, i went through the documentations to find out what are the requirements to communi...
by saad
Wed Nov 15, 2017 1:00 am
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hello there, I just received the SCX11 motor controller and the setup worked with my software, now I want to know how to power them both, my current setup is connecting both of the motor controller and driver separately to a regulated DC power supply, I am thinking of using two 12 V lead acid batter...
by saad
Wed Oct 04, 2017 6:48 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hello there, You mentioned that I could use a terminal software to send ASCII commands to communicate with the motor correct, lets just say I buy the SCX11 motor controller and follow the protocol and use tera term as the terminal software, will it work? Also can I use connect the SCX11 controller v...
by saad
Tue Sep 19, 2017 11:48 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hey there, I've looked into the documentation of SCX11 controller, I was wondering wonder if I could communicate via serial port and send characters such as, UU=DEG/r/nDPR=360/r/nMR=500/r/n .. etc In the documentation, page 67, it states that RS-232C and usb are the same, so my question is if I send...
by saad
Mon Sep 18, 2017 10:08 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hey there, I've looked into the SCX11 controller, it mentioned this on page 10, http://www.orientalmotor.com/products/pdfs/opmanuals/HM-60079E.pdf, Here, let us introduce how to command an operation by directly communicating with the SCX11. First, click the [Terminal] tab and open the terminal scree...
by saad
Thu Sep 14, 2017 9:12 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hey there, Currently I'm using pulse inputs to control the system, I've read the manual and noticed that the output pins give out a 3V signal once trigger, output pin 9, OUT4, Control output 4 (MOVE), will give out a signal once the motor is moving, I tested my program to send pulses to move the mot...
by saad
Wed Sep 13, 2017 6:20 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

Re: AZ Series Interface Control Documentation (ICD)

Hey there,

The driver model is AZD-K, I've noticed through the MEXE02 software it's possible to move the motor, is there any link or pdf file of the Interface Control Documentation (ICD) / Command set that I can use to communicate without the use of the software.
by saad
Tue Sep 12, 2017 11:32 pm
Forum: Stepper Motors and Controls
Topic: AZ Series Interface Control Documentation (ICD)
Replies: 16
Views: 4912

AZ Series Interface Control Documentation (ICD)

I've recently purchased the AZ Series stepping motor and driver package, I need to control it through serial com, I have tried the MEXE02 software and would like move the motor without using the software, is there any documentation or example that will guide me into move the motor via serial com, I ...

Go to advanced search