Search found 191 matches

by om_tech_support_JS
Thu Apr 06, 2017 12:30 pm
Forum: Stepper Motors and Controls
Topic: PLEASE HELP! How to send info from PLC to SCX11.
Replies: 3
Views: 1101

Re: PLEASE HELP! How to send info from PLC to SCX11.

Hi jesus666viz, In regards to your request, once the ID number has been assigned using the command ID= ( page 257 ), then you can use the command @ ( page 179 ) to select the controller. Once the controller is selected, then you can use the RUN command ( page 330 ) to execute a sequence. http://www....
by om_tech_support_JS
Wed Apr 05, 2017 9:36 am
Forum: Stepper Motors and Controls
Topic: PLEASE HELP! How to send info from PLC to SCX11.
Replies: 3
Views: 1101

Re: PLEASE HELP! How to send info from PLC to SCX11.

Hi jesus666viz, For support on the PLC, you would need to contact the manufacturer of the PLC. As for the SCX11 controller, it is programmed by RS232C. Typically, you would use our GUI software to program the controller and use the PLC to trigger inputs for selecting your program. SCX11 Software: ht...
by om_tech_support_JS
Wed Mar 22, 2017 9:27 am
Forum: Stepper Motors and Controls
Topic: HELP! How to program PKA566KD stepper motor
Replies: 1
Views: 872

Re: HELP! How to program PKA566KD stepper motor

Hi JZ, In regards to your question, the PKA566KD stepper motor is an All-in-One stepper motor package. The driver which is part of the All-in-One system is a built-in controller (stored data) type driver. This product has the label FLEX which means that you can control the motor via I/O, Modbus, or ...
by om_tech_support_JS
Wed Mar 22, 2017 9:07 am
Forum: Stepper Motors and Controls
Topic: What dows "Holding Torque Tb"'s "b" mean?
Replies: 4
Views: 1349

Re: What dows "Holding Torque Tb"'s "b" mean?

Hi colemanlee, The "calculation software" and attachment which you provided are not available for the OM USA branch. From the part number, PKP268D28A-L which is the Japanese version, I can verify that the Holding torque is 2.3 N-m and the Rotor Inertia is 490 x10^-7 [kg-m^2]. For the true ...
by om_tech_support_JS
Mon Mar 20, 2017 7:43 am
Forum: General Discussion
Topic: Where is 162VDC speed – torque graph for UMK245BA?
Replies: 1
Views: 825

Re: Where is 162VDC speed – torque graph for UMK245BA?

Hi colemanlee, It appears that the same graph was used in this post. Since this post was made, the UMK245BA package has been discontinued. However, you can still reference the speed torque curve of the UMK245BA package from the link below: http://catalog.orientalmotor.com/image?cid=1002&imgname=...
by om_tech_support_JS
Mon Mar 20, 2017 7:05 am
Forum: Stepper Motors and Controls
Topic: What dows "Holding Torque Tb"'s "b" mean?
Replies: 4
Views: 1349

Re: What dows "Holding Torque Tb"'s "b" mean?

Hi colemanlee,

In regards to your question, is there a specific product which you are referring to that shows the Holding Torque as Tb? Was this reference pulled from a manual or our catalog?
by om_tech_support_JS
Fri Mar 17, 2017 11:45 am
Forum: Stepper Motors and Controls
Topic: Alpha step motor and driver help
Replies: 3
Views: 1391

Re: Alpha step motor and driver help

Hi gregouellette, The current motor and driver part numbers which you are using are part of a closed loop system. Therefore, there is built-in resolver feedback between the motor and the driver. In order for the motor and driver to function properly, they need to be operated together. The current dr...
by om_tech_support_JS
Wed Mar 15, 2017 8:11 am
Forum: General Discussion
Topic: Alpha Stepper and Drive
Replies: 1
Views: 865

Re: Alpha Stepper and Drive

Hi gregouellette,

Please reference the original forum post which includes pictures of the application:
viewtopic.php?f=3&t=4693&p=8703#p8703
by om_tech_support_JS
Wed Mar 15, 2017 7:56 am
Forum: Stepper Motors and Controls
Topic: Alpha step motor and driver help
Replies: 3
Views: 1391

Re: Alpha step motor and driver help

Hi gregouellette, In regards to your application, we unfortunately do not offer the smooth stepper control board. You would need to purchase one of these through a third party. For the breakout board, the closest option that we offer is a terminal block unit. You would be able to purchase the CC36T1...
by om_tech_support_JS
Wed Mar 08, 2017 11:52 am
Forum: General Discussion
Topic: Need solution to my switching power supply circuit
Replies: 2
Views: 1116

Re: Need solution to my switching power supply circuit

Hi Jeenie,

In regards to your post, your English is very good. Unfortunately we may not be the best people to give professional advice since we are product experts; not machine builders, system integrators, nor professional electricians.
by om_tech_support_JS
Tue Mar 07, 2017 9:05 am
Forum: Stepper Motors and Controls
Topic: Maximum temperature of a step motor
Replies: 5
Views: 8621

Re: Maximum temperature of a step motor

Hi Andyson, In regards to your request, we have other forum topics better related to the use of the stored data products. For an initial walk through of using the stored data type drivers, please reference the link below: http://forum.orientalmotor.com/viewtopic.php?f=26&t=716&p=1145&hil...
by om_tech_support_JS
Thu Feb 23, 2017 1:54 pm
Forum: Stepper Motors and Controls
Topic: emp 402 serial pc control
Replies: 1
Views: 881

Re: emp 402 serial pc control

Hi axlpotito, The EMP402 controller uses RS232C communication in order to write sequences to the controller. You will need to follow the appropriate command syntax in order for the controller to accept the sequence which you write. You can reference section 9 (starting on page 53 ) of the manual lin...
by om_tech_support_JS
Wed Feb 22, 2017 2:48 pm
Forum: Stepper Motors and Controls
Topic: Drive a Sanyo denki Motor by wexta driver
Replies: 6
Views: 1651

Re: Drive a Sanyo denki Motor by wexta driver

Hi Hadi, The rated output current is the maximum current that the driver can output to the motor. For the CSD5814N- driver, the rated ouput current is 1.4 Amps. You can then adjust the RUN current dial to adjust the current sent to the motor. You would need to follow the steps on page 15 of the manu...
by om_tech_support_JS
Wed Feb 22, 2017 2:02 pm
Forum: Speed Control Systems
Topic: Hollow Shaft Flat Gearhead series motor Allowable Load and Misalignment
Replies: 10
Views: 2705

Re: Hollow Shaft Flat Gearhead series motor Allowable Load and Misalignment

Hi ax20, For the information that you are looking for, it would be better to reference the Load Torque – Driver Input Current graphs that are shown on page G-65 (electronically page 26) of the link below: http://www.orientalmotor.com/products/pdfs/2012-2013/G/usa_tech_product.pdf These graphs are th...
by om_tech_support_JS
Wed Feb 22, 2017 12:58 pm
Forum: Linear & Rotary Actuators and Controls
Topic: Can the EZED2 be substituted for the discontinued EZED1?
Replies: 12
Views: 7303

Re: Can the EZED2 be substituted for the discontinued EZED1?

Hi xeoner, The EZS6-40M actuator and the EZMC36I driver require the use of the EZED1 software and cannot be used on the EZED2 software. The EZED1 software is too large to include in this forum, but it is something that can be shared via google drive. Please note that this unit requires an interface ...
by om_tech_support_JS
Mon Feb 20, 2017 9:52 am
Forum: Linear & Rotary Actuators and Controls
Topic: Can the EZED2 be substituted for the discontinued EZED1?
Replies: 12
Views: 7303

Re: Can the EZED2 be substituted for the discontinued EZED1?

Hi xeoner,

Do you have the part number of your EZS package? Otherwise, do you have the part numbers for your actuator and driver? With this information, I can help in selecting the appropriate product from the listings.
by om_tech_support_JS
Mon Feb 20, 2017 9:38 am
Forum: Stepper Motors and Controls
Topic: Drive a Sanyo denki Motor by wexta driver
Replies: 6
Views: 1651

Re: Drive a Sanyo denki Motor by wexta driver

Hi Hadi, Our motors and drivers have been tested together. This testing helps in designing the drivers to provide a system of current control that produces the least possible vibration out of the motors. Apart from that, we also put emphasis on our manufacturing processes in order to produce a motor...
by om_tech_support_JS
Mon Feb 20, 2017 8:57 am
Forum: Stepper Motors and Controls
Topic: MEXE02 - Question
Replies: 6
Views: 1392

Re: MEXE02 - Question

Hi damdayy, There is no way to increase/override the maximum step number that each operation can be given as it is the maximum value that can be written to the driver. One thing that you can do is to disable the " Software Overtravel ." This way, you can continue to move the motor in one d...
by om_tech_support_JS
Mon Feb 20, 2017 8:33 am
Forum: Stepper Motors and Controls
Topic: Controlling SCX11 using C++
Replies: 3
Views: 1054

Re: Controlling SCX11 using C++

Hi cpede, You can use a terminal software which communicates via RS232C in order to send the ASCII commands to the SCX11 controller directly. Tera Term is an example of the terminal software. Otherwise, if you download our Immediate Motion Creator (IMC) for SCX11 Software, v2.11, you will be able to...
by om_tech_support_JS
Fri Feb 17, 2017 3:40 pm
Forum: Servo Motors & Controls
Topic: Single phase power for NX640AS-3,
Replies: 1
Views: 926

Re: Single phase power for NX640AS-3,

Hi Steve, In regards to your question, a VFD (otherwise known as an inverter) is used to control the speed of a three-phase motor. Typically a VFD will take a specific input voltage (in your example a single-phase input) and output a three-phase voltage to the motor. The intended use of the VFD is t...
by om_tech_support_JS
Fri Feb 17, 2017 2:44 pm
Forum: Stepper Motors and Controls
Topic: MEXE02 - Question
Replies: 6
Views: 1392

Re: MEXE02 - Question

Hi damdayy, With the AR series, you are limited to 4 linked motions. As previously stated, the AZ series does not have that limitation. Looking further at the AR series, you would be able to achieve more of the functionality that you are looking for by adding a PLC to the system. You could then have...
by om_tech_support_JS
Fri Feb 17, 2017 2:28 pm
Forum: Stepper Motors and Controls
Topic: Controlling SCX11 using C++
Replies: 3
Views: 1054

Re: Controlling SCX11 using C++

Hi cpede, The SCX11 is our universal stepper motor controller which will provide the pulse and direction signals to a pulse input type driver. You can then control the stepper motor via USB, RS-232C, or CANOpen. The SCX11 uses a specific syntax which is different than C++. You will need to use ASCII...
by om_tech_support_JS
Thu Feb 16, 2017 11:31 am
Forum: Stepper Motors and Controls
Topic: MEXE02 - Question
Replies: 6
Views: 1392

Re: MEXE02 - Question

Hi damdayy, I believe the product that you are referring to is our AR series of stepper motors. With this series, a maximum of 4 operations can be linked together. There is also no option to create a loop. In order to create a loop, you would need a PLC to trigger the first input once the linked mot...
by om_tech_support_JS
Mon Feb 13, 2017 3:06 pm
Forum: Stepper Motors and Controls
Topic: Upgrading Techno LC4896
Replies: 3
Views: 1091

Re: Upgrading Techno LC4896

Hi Steve, In regards to your post, the SCX11 is our external controller part number. This controller is a stored program type controller. This controller will provide the pulse and direction signals to the pulse input type driver. You will then be able to control the motor using various serial ports...
by om_tech_support_JS
Tue Feb 07, 2017 1:25 pm
Forum: Stepper Motors and Controls
Topic: Upgrading Techno LC4896
Replies: 3
Views: 1091

Re: Upgrading Techno LC4896

Hi Steve, In regards to your questions, the FLEX type driver is a built-in controller (stored data) type driver. This package product allows for controlling the motor through I/O , Modbus (RTU/RS-485), or an FA Network . The "Stored Data" classification means that you will need to save the...

Go to advanced search